April 5, 2019

APTRANSCO Question Paper with Solutions provided by Institute of Electrical & Electronics Engineering (ieee), , Hyderbad. APTRANSCO/APGENCO Assistant Engineer AE Electrical Previous Question Papers | Indian Shout. Like. 0. Home. About. Contact us. ELECTRICITY. APGENCO APGENCO/APTRANSCO Online Mock test AP TRANSCO PREVIOUS QUESTION PAPER-ELECTRICAL. 1.

Author: Shashakar Bami
Country: Philippines
Language: English (Spanish)
Genre: Politics
Published (Last): 5 December 2006
Pages: 188
PDF File Size: 16.37 Mb
ePub File Size: 16.76 Mb
ISBN: 341-7-36500-985-4
Downloads: 51917
Price: Free* [*Free Regsitration Required]
Uploader: Nishura

Heat convection, radiation, leectrical conduction all are takes place in a Ice b Boiler c Refrigerator d Flue gases in pipe Ans: Get my banner code Make flash banner.

APTRANSCO AE Question Paper and Answer Key Released – Electrical, Civil Engineering

Which is the most suitable power device for high frequency more kHz switching application? Transient stability can be improved by a By putting series capacitor b By using dynamic resister c Auto re-closers d All of the above Ans: Field flux production In Induction motor Slip frequency of rotor current, when rotor speed is Nr.

Total stator losses are 1 KW. When Alternator excitation increases aptrnsco machine is operating at lagging power factor then a I increase b I decreases c No effect on current d None Ans: Elecrtical Gauss Seidel method the following factors are influenced for operation a Acceleration factor b Selection of slack buss c Both d None Ans: In an induction machine, if the air gap increased previojs Speed will be reduced b Efficiency will be improved c Power factor will be lowered d Breakdown torque will be reduced Ans: When moving iron meter is used to measure d.

The following element retains it energy after source is disconnected a Resister b Inductor c Capacitor d Thermistor Ans: If series field is short circuited, then the armature current and speed will a Both increases b Both decreases c Increases and decreases electrica Decreases and increases Ans: The two watt meters measurement the ratio of two meter readings is — 1-sqrt3: Core loss component current decreases, Magnetizing component current decreases Subscribe To Posts Atom.


All of ptevious above Find us on Facebook Electricalengineerz.

Posted by Srinivas goud at 8: No build up of voltage Good regulation means a Less fluctuations from no-load to full-load b c d Ans: For parallel operation of transformer at no load, then load shared are equal when a Impedance is proportional with respect to own KVA rating b c d Ans: Harmonics are eliminated by using a Skewing of rotor b Distribution winding c Short pitch winding d All of the above Ans: Which of the following plant is having lowest load factor?

In ceiling fan the angle between auxiliary winding a main winding is a 0 deg b 90 deg c deg d deg Ans: Lag net work Flue gases coming out from furnace is first going through a Turbine b Economizer c Air pre-heater d Chimney Ans: Ebooks Electrical engg vol-1 Electrical engg vol-2 Electrical engg vol-3 Electrical engg vol A dc cumulatively compounded motor delivers rated load torque at rated speed.

Va and Vb are negative sequence component voltages the difference angle between Va and Vb with respect to Va is a b c d Ans: Linkbar Home careers blogs Apcpdcl. I changed my font at thecutestblogontheblock.

[SOLVED] APTRANSCO AE Previous Papers PDF [Assistant Engineer]

Power factor will be lowered If direction of rotation is reversed, then machine will a Build up its voltage with same polarity b Build up its voltage with opposite polarity c No build up of voltage d None Ans: The phase lead compensation is used to a Increase rise time and decrease overshoot b Decrease both rise time and overshoot c Increase both rise time and overshoot d Decrease rise time and increase overshoot Ans: Practical method of improving string efficiency a Increasing crass arms length b Using different size of insulators c Using different insulator materials d Using of guard rings Ans: Mho relay is usually employed for the protection of a Short lines only b Medium lines only c Long lines only d Any line Ans: Temperature of electrode in Arc furnace is a deg b deg c deg to deg d deg Ans: Moving coil in dynamometer wattmeter connected a In series with fixed coil b Across supply c In series with load d Across load Ans: For a single-phase a.


When sine wave is given as input to Schmitt trigger then its generates a Sine wave b Saw tooth wave c Triangle wave d Square wave Ans: Low-pass filter function ii.

For SR latch whent the out put is undesirable a 0, 0 b 1, 0 c 0, 1 d 1, 1 Ans: AE electrical previous papersap genco electrical sub engineers key paperap transcoelectrical previous paperrstranscotransco previous question papertrascno electrical.

Vab is reference then angle between Vab and Ib is a deg b deg c deg d deg Ans: Less fluctuation from no-load to full-load Long lines only 2. Decrease rise time and increase overshoot In bode plot the point which separates the lower and upper frequencies is called a Critical point b Cut-off point c d Ans: In a shaded pole motor, shaded rings are used to a Field flux production b c d Ans: