LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.
|Published (Last):||7 February 2004|
|PDF File Size:||14.32 Mb|
|ePub File Size:||16.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature. The LM also provides excellent stability vs. This point occurs when the device is required to sink approximately 1. The LM is suitable datahseet limited-temperature operation. Contact the factory for availability of devices with proven long-term stability.
Avoid such overloads for voltages ddatasheet than a 20 V, for more than 5 seconds, or, at high ambient temperatures. The devices have a They are based on a buried zener reference as pioneered in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending.
Pin numbers for H, M or N packages. Capacitance in the Typical Performance Characteristics section show graphically that a l,607 capacitance of 0.
There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. Alternatively, a shield foil can be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively lm6077 as a guard against AC coupling and DC leakages.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
The curves showing the Noise vs. For example, if the output were trimmed up to However, dayasheet overloads at high ambient temperatures, as a prolonged short-circuit may cause the daasheet temperature to exceed the Absolute Maximum Temperature. This datasheet has been downloaded from: To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground.
LM Datasheet PDF – National ->Texas Instruments
The output can sink current as well as source it, but the output impedance is much better for sourcing current. Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Datasheer.
These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, dahasheet stray capacitance could couple noises into the output. Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Tempco linearity at temperature extremes.
Consult factory for availability of devices with tighter Accuracy and Tempco Specifications.
The LM is recommended for applications where the highest stability and lowest noise is required over the full military temperature range. These pins may be cut off if desired. The capacitor used should be a low-leakage type. Documents Flashcards Grammar checker. The trim pin pin 5 should also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere. The output is short-circuit-proof to ground.
LM607 View Datasheet(PDF) – National ->Texas Instruments
Life support devices or systems datashheet devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected datasheeet result in a significant injury to the user.
Ceramic capacitors may seem to do the job, but are not recommended for production use, as the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise. A military RETS electrical test specification is available on request. National Semiconductor Europe Fax: Consult factory for availability of devices with Guaranteed Long-term Stability.
These limits are not to be used to calculate outgoing quality levels. LM see curve above: The output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. Thermal regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW.
Regulation is measured at constant temperature using pulse testing with a low duty cycle.
Unless otherwise noted, these conditions apply: In some applications it may be advantageous to pre-load the output to either Vin or to ground, to avoid this crossover point. Tsimshatsui, Kowloon Hong Kong Tel: If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur.
In Sinking mode, connect 0. Do not connect anything to these datasheeet, or improper operation may result.
A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0. The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. The device does not include a thermal shut-down circuit.